Quickie Groove Technické informace Strana 23
- Strana / 66
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Quickie Groove 23
.EMS
6.0 Seating
6.1 Firm seat board
The firm seat board is designed to allow pressure relief cushions
such as Jay to be used.
WARNING!
If retro-fitting the firm seat board you must ensure the two
retaining screws and collars are fitted and that the seat hooks are
located behind them prior to use (Fig 6.1). Failure to do this may
result in the seat tipping up and possibly causing injury.
6.2 Seat cushions
Seat cushions supplied by Sunrise Medical will have Velcro®
strips that correspond to patches on the seat.
WARNING!
You must ensure these are aligned prior to using the wheelchair.
Other cushions used should also have Velcro® strips in a similar
position to ensure the cushion does not slip off the seat.
The seat cushions, supplied by Sunrise Medical all have
removable covers.
6.3 Changing seat depth on the standard rehab seat
To change the seat depth, loosen the two clamps on each side
of the seat rails. The backrest can now be moved to the desired
position along the seat rail. Tighten the four bolts at the clamps
on each side of the backrest. Make sure you have at least 1cm
of the rear of the seat rail tube left when adjusting the maximum
seat depth (Fig. 6.2 and 6.3).
6.4 Changing seat height
To change the seat height loosen the four nuts of the receivers
of the seat module Interface (Fig. 6.4 and 6.5) on the bottom
frame with two 13 mm spanners. Take the bolts off the frame.
WARNING!
Make sure the top frame does not trap your fingers.
Hold the top frame securely in the up position. Adjust the seat
height by choosing your required hole position of the module
interface and replace the bolts and the nuts. Tighten them
securely.
6.5 Removable seat covers
The seat covers are all fully removable using zips or Velcro
®.
Once brackets are removed seat covers can be removed. The
zip for the backrest is located on the under side of the cushion.
6.6 Backrest removal and retting (rehab & comfort seat)
Although there are a variety of back upholsteries which can be
used on the GROOVE backrest structure, they all attach and
release in the same way. To remove the standard backrest (Fig.
6.6 and 6.7) loosen the screws on the base of the backrest and
pull up the back. To attach the backrest, repeat the process in
reverse.
WARNING!
You must ensure the two screws are securely locked in position
and the backrest is correctly and firmly attached prior to using
your chair.
Fig. 6.1
Fig. 6.2
Fig. 6.3
Fig. 6.4
Fig. 6.5
Fig. 6.6
Fig. 6.7
- Instructions for Use 1
- User Information 2
- Quickie Groove 3 3
- Rear/Front Wheel Drive 5
- Mid Wheel Drive 5
- 1.0 Your Wheelchair 6
- 2.0 How to use this manual 6
- Quickie Groove 7 7
- 8 Quickie Groove 8
- 3.2 Label explanations 8
- WARNING!WARNING! 9
- Fig. 4.1 10
- Fig. 4.2 10
- Fig. 4.5 11
- Fig. 4.4 11
- Quickie Groove 12
- Quickie Groove 13 13
- Fig 4.6 and Fig 4.7) 15
- (RWD base only) 16
- and removal procedure 16
- Quickie Groove 17 17
- 5.5 and Fig. 5.6) 18
- Fig. 5.8) 19
- Fig. 5.9) 19
- Fig. 5.18 21
- Fig 5.19): 22
- 6.0 Seating 23
- Fig. 6.8) 24
- Quickie Groove 25 25
- Quickie Groove 27 27
- WARNING! 28
- Quickie Groove 29 29
- Fault code Possible cause 30
- 9.0 R-net Control System 31
- Fig.10.3 33
- Fig. 10.4 34
- Fig.11.1 35
- Fig. 11.2 35
- 12.0 Batteries and charging 37
- Fig. 12.8 39
- Fig. 12.7 39
- 13.0 Transportation 41
- Quickie Groove 43 43
- Quickie Groove 45 45
- Quickie Groove 47 47
- Quickie Groove 49 49
- Fig. 13.55 50
- Fig. 13.56 50
- Fig. 13.57 50
- Fig. 13.58 50
- Fig. 14.1) 51
- Fig. 14.2) 51
- Fig. 14.3) 51
- Fig. 14.4) 51
- Fig. 14.5 52
- Fig. 14.6 52
- Fig. 14.7 52
- Fig. 14.8 52
- Fig. 14.9 53
- Fig. 14.10 53
- Fig. 14.12 53
- Fig. 14.13 53
- Fig. 14.11 53
- Quickie Groove 55 55
- Fig. 14.18 57
- Fig. 14.19 57
- Quickie Groove 59 59
- Quickie Groove 61 61
- 16.0 Service History 63
- 17.0 Disposal 63
- Quickie Groove 65 65
- Pt.No.000690665 66
Související produkty a manuály pro ne Quickie Groove
ne Quickie Pulse Uživatelský manuál
(6 stránky)
(6 stránky)
ne Quickie QRi Uživatelský manuál
(5 stránky)
(5 stránky)
ne Quickie QM-7 Series Uživatelský manuál
(6 stránky)
(6 stránky)
ne Quickie QRi Uživatelský manuál
(8 stránky)
(8 stránky)
ne Quickie Pulse Uživatelský manuál
(9 stránky)
(9 stránky)
ne Quickie Jive Specifikace
(60 stránky)
(60 stránky)
ne Quickie Rhythm Uživatelský manuál
(4 stránky)
(4 stránky)
ne Quickie Q7 Adjustable Uživatelský manuál
(24 stránky)
(24 stránky)
ne Quickie Argon2 Uživatelský manuál
(38 stránky)
(38 stránky)
ne Quickie Salsa M Uživatelský manuál
(170 stránky)
(170 stránky)
ne Quickie S-636 Uživatelský manuál
(7 stránky)
(7 stránky)
ne Quickie Rumba Modular Uživatelský manuál
(86 stránky)
(86 stránky)
ne Quickie S-646 SE Uživatelský manuál
(20 stránky)
(20 stránky)
ne Quickie Xenon SA Uživatelský manuál
(8 stránky)
(8 stránky)
ne Quickie Groove Uživatelský manuál
(355 stránky)
(355 stránky)
ne Quickie Jive Uživatelský manuál
(196 stránky)
(196 stránky)
ne Quickie 2HP Uživatelský manuál
(4 stránky)
(4 stránky)
ne Quickie Hula Uživatelský manuál
(4 stránky)
(4 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.127 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce